Can anyone bend 1" steel round tube or know where to find 1" OD 90° elbow

[drift_g35]

Making a roof rack and dont have a pipe bender. I am having a hard time finding 1" 90° elbows. So I am thinking I will have to find someone to make the bend for me. Hoping to keeping it on the cheap end. Any suggestions?

[jerrymrc]

"V" notch it and weld it back up Or this. http://www.harborfreight.com/http-www-harborfreight-com-12-ton-hydraulic-pipe-bender-32888-html.html

[Great-Kazoo]

I have one of these sitting here. Drive up use it, put it away, enjoy. If need be you can also tack or weld the assy.
http://www.harborfreight.com/http-ww...2888-html.html (http://www.harborfreight.com/http-www-harborfreight-com-12-ton-hydraulic-pipe-bender-32888-html.html)

[Colorado_Outback]

Never mind it's in the title.

[sniper7]

Yeah...work out and bend the thing over your knee.

[Colorado_Outback]

Just doing some goggling.
http://www.zoro.com/g/00122277/k-G1123157?utm_source=google_shopping&utm_medium=cpc&utm_campaign=Google_Shopping_Feed&gclid=Cj0KEQjw6J2eBRCpqaW0857k9p4BEiQAWarYbNhUHmxI _U7EgKnufhXuIRbbx7LVjKOiUOH2GlxcRl0aAshf8P8HAQ

You will be able to join the stainless to your mild tube with a mig.

Some more options..
http://www.sharpeproducts.com/store/bent-90-stainless-steel-steel-aluminum-pipe-tube-elbows?pagenumber=2

[BPTactical]

RoadRunner Fabrication: http://www.roadrunnerfabrication.com/
They are about 65-6th and just east of Broadway.

Ask for Dan, tell him Bert sent you.

[SideShow Bob]

Bending EMT, GRC 1" conduit or is it dimensional steel tubing ?

[Great-Kazoo]

This get resolved , OP find a place to bend tubing?

[Sparky]

Bending EMT, GRC 1" conduit or is it dimensional steel tubing ?

If it is something like this I can bend it.

[drift_g35]

Bending EMT, GRC 1" conduit or is it dimensional steel tubing ?

Its dimensional.

Jim. Id love to just come over and use your bender but that is quite the drive. I appreciate it though. I might stop by a few places that were mentioned above.

[drift_g35]

Just doing some goggling.
http://www.zoro.com/g/00122277/k-G1123157?utm_source=google_shopping&utm_medium=cpc&utm_campaign=Google_Shopping_Feed&gclid=Cj0KEQjw6J2eBRCpqaW0857k9p4BEiQAWarYbNhUHmxI _U7EgKnufhXuIRbbx7LVjKOiUOH2GlxcRl0aAshf8P8HAQ

You will be able to join the stainless to your mild tube with a mig.

Some more options..
http://www.sharpeproducts.com/store/bent-90-stainless-steel-steel-aluminum-pipe-tube-elbows?pagenumber=2


Isnt it quite hard to weld stainless to mild? Ive never tried that. I tried welding stainless to stainless with stainless wire but had a 75/25 gas and I got no penetration.

[BPTactical]

Isnt it quite hard to weld stainless to mild? Ive never tried that. I tried welding stainless to stainless with stainless wire but had a 75/25 gas and I got no penetration.

Depends on the welding process used. MIG it's tough to do but easy peasy with TIG.

[Mtn.man]

We got a 1" tube die and bender.

[Dave]

Not being sure of what kind of tube you have though I would think one of the performance exhaust shops in the area could either mandrel or crush bend 1" steel easy since they do it with pipes up to 3". As for joining mild steel to SS I'd use TIG if it's available.