AK gurus, please help!

[Dr_Fwd]

Hey guys,
I'm buying a couple of those receivers listed in for sale section. From what I understood these are polish made 7.62x39mm receivers.
My question is - where I can get the parts kit to "fit" those receivers and what are the prices for ak prts kits now days?

Thank you!
[Beer]

[Great-Kazoo]

Hey guys,
I'm buying a couple of those receivers listed in for sale section. From what I understood these are polish made 7.62x39mm receivers.
My question is - where I can get the parts kit to "fit" those receivers and what are the prices for ak prts kits now days?

Thank you!
[Beer]



Brycom's? grab em while you can, I have a few. Here's some info & links for kits. Also contact Tristan a member here he has AK kits.

It will work with any AK47 1mm stamped parts kit


http://www.nodakspud.com/page2.htm

https://www.apexgunparts.com/index.php/cPath/51

[zteknik]

We would have to wait for our inhouse pricewatcher,Rachel Ray,Jr should know all the up to minute listings on vendors that have them in stock [Coffee]
The upper rails have to be trimmed down and all the holes have to be located and drilled out.Between a few of us we plan on getting the drillout jig,and I allready have a set of top rail scribe jigs.

I feel another build party in the works.[Tooth]

[Great-Kazoo]

We would have to wait for our inhouse pricewatcher,Rachel Ray,Jr should know all the up to minute listings on vendors that have them in stock [Coffee]
The upper rails have to be trimmed down and all the holes have to be located and drilled out.Between a few of us we plan on getting the drillout jig,and I allready have a set of top rail scribe jigs.

I feel another build party in the works.[Tooth]


Mid sept or early OCT my place.

[jreifsch80]

the best prices are apex gun parts right now

[Dr_Fwd]

Thank you guys!
I'm in for next build party! (please)

[Dr_Fwd]

the best prices are apex gun parts right now

I checked the apex gun parts. Is these receivers gonna work for Yugo m64?

[hghclsswhitetrsh]

So do you stamp your serial number that comes with the kit onto the receiver? Pardon my ignorance.

[Great-Kazoo]

So do you stamp your serial number that comes with the kit onto the receiver? Pardon my ignorance.


ABSOLUTELY NOT. That could imply you are , may, could, would, might be manufacturing them for resale. This is merely a parts kit similar to say an 80% AR lower that you were able to form in to a firearm. This is not something you would sell for profit, or constantly crank out, to again sell.

[zteknik]

I checked the apex gun parts. Is these receivers gonna work for Yugo m64?
For the m64 you would need reciever repair plates.So the answer would be no.
The m64 is a milled reciever.Allthough I've seen guys grind /mill down the front stub to use it like a regular trunnion and use a reciever or a flat.
You could scrounge up a Yugo front trunnion and press and pin your barrel into that,but you would still need a different reciever.The yugo's are 1.4mm as opossed to 1mm of the standard recievers.Chineese is also 1.5

[Great-Kazoo]

For the m64 you would need reciever repair plates.So the answer would be no.
The m64 is a milled reciever.Allthough I've seen guys grind /mill down the front stub to use it like a regular trunnion and use a reciever or a flat.
You could scrounge up a Yugo front trunnion and press and pin your barrel into that,but you would still need a different reciever.The yugo's are 1.4mm as opossed to 1mm of the standard recievers.Chineese is also 1.5


F$%^&k First we have Rachael and now who......Paula Deen, Alton, I know, I know........Cat Cora. [ROFL1]

[zteknik]

F$%^&k First we have Rachael and now who......Paula Deen, Alton, I know, I know........Cat Cora. [ROFL1]
Rachel Ray was out sniffing the coz boquet's so sombody had to fill in :D

[Great-Kazoo]

Rachel Ray was out sniffing the coz boquet's so sombody had to fill in :D

[ROFL1][Beer][ROFL3][ROFL2][Help][NoEvil]

[CrufflerSteve]

When you're looking at kits anythings milled, Yugo or RPK probably won't work with those receivers. Underfolders would require a lot of work on the back of the receiver.

Apex is getting low on kits. I see there are still some at: http://whatacountry.com/parts-kits.aspx

Steve

[jreifsch80]

Also an m64 has a threaded barrel like a type 1-3 ak47 so it would require turning the threads down for use in a stamped trunnion, apex does have cut up m64 receivers so a compliant reweld can be done using receiver sections as repair plates I know I'm a little late to the party eyegore had to fill in for me ;)

[kwando]

Subscribed as I picked one up... Can't wait to do this build

[DFBrews]

One in hand as well I have no friken clue what i need to be looking for parts kit wise except not milled and i probably can not do the underfolder

[Dr_Fwd]

Underfolder is what I want..

[bryjcom]

here is the blue prints for the AK receiver. This could be used to locate holes in the polish receivers. You should verify locations before drilling

http://www.ar15.com/content/manuals/AK47ReceiverPlanRev2.pdf

[zteknik]

here is the blue prints for the AK receiver. This could be used to locate holes in the polish receivers. You should verify locations before drilling

http://www.ar15.com/content/manuals/AK47ReceiverPlanRev2.pdf
Is that Dr Strangeloves print? ;) We used it when flats were just made from what you had laying around before regular pre mades. [Coffee]
I have a disk with all the pertinent info if anybodys in the springs and wants a copy lemme know...

I also made some templates from some of the flats as well-their just coppied onto thicker paper but I cut the holes out and spray over them like a stencil...

[Great-Kazoo]

Is that Dr Strangeloves print? ;) We used it when flats were just made from what you had laying around before regular pre mades. [Coffee]
I have a disk with all the pertinent info if anybodys in the springs and wants a copy lemme know...

I also made some templates from some of the flats as well-their just coppied onto thicker paper but I cut the holes out and spray over them like a stencil...

Hand 1 or 2 off to RR today.

[zteknik]

Hand 1 or 2 off to RR today.
Will do.

[jreifsch80]

I have bobs rosetta stone of ak building (binder with lots of print offs) he has templates as I also have a bunch of strange love prints too. I'm thinking of getting a drilling jig for the polish blanks, would anyone be interested in using it as well?