How to clean sand out of AR

Fill with old Barbasol shaving foam, scrub, break it down in the shower to rinse.

Quote:

---

Originally Posted by BPTactical

If my "buddy" challenged me to that I would tell him to fuck himself. He can go buy his own damn AR and find out.

---

Duh... [Stick]

Gotta be better ways to make $20.

Quote:

---

Originally Posted by sniper7

I tired that and it works awesome, sand pops out of all the crevices.

---

See guys? it's totally safe! [microwave]

Quote:

---

Originally Posted by coloccw

Fill with old Barbasol shaving foam, scrub, break it down in the shower to rinse.

---

Works good

Quote:

---

Originally Posted by Rooskibar03

May I suggest one of these.

---

You have one? How do you like it? AR-15 uppers are good, but not lowers, right? No Aluminum?

Quote:

---

Originally Posted by Brian

You have one? How do you like it? AR-15 uppers are good, but not lowers, right? No Aluminum?

---

What is an areare-15 upper receiver made of?

Sorry, I didn't word that very well, but that was my point. I've heard very mixed reviews on what you can and cannot use in one of these. Hornady clearly advertises it's made for cleaning upper receiver groups and small parts, but then the vast "wisdom" of the internet seems to claim you can't dump your lower in it, or it will dissolve into fairy dust or something. I shoot a lot suppressed, and the idea that I could disassemble the gun and drop it in a tank, dirty mags and all, is really appealing. But not if it's going to somehow mess with the anodizing or something.

Would really like to hear from someone who has dunked their AR a few dozen times.

Quote:

---

Originally Posted by rbeau30

On a more serious note, do all of you put a lot of oil in your ARs? All I really do is clean with CLP, thin last coat of CLP after surfaces clean and quick wipe dry.

---

I run my ars wet (Mobil 1)

http://www.slip2000.com/blog/s-w-a-t...ine-filthy-14/

The maker of my tank (Sharper Tek) warns that "mirror finishes on aluminum can be dulled" from cleaning in an ultrasonic tank, and recommend use of a "dispersion plate" they sell if you're going to be cleaning mirror-finished aluminum pieces. I don't believe the same applies to the hard-coat anodized surfaces of an AR upper and lower, but who knows?

I use simple green aircraft as my detergent, and haven't noticed any negative effects on the uppers or lowers I've cleaned in my tanks, but I haven't gone through a dozen cycles on any of the parts yet, as I only dunk the rifles if they're extra filthy (usually after MG rentals), otherwise I still just clean by hand. I've also done big batches of magazines in my tanks, using one for a simple green cleaning pass, then a quick dunk in light oil to displace the water and lubricate them before letting them drip drain and air dry.

I have several smaller tanks I use for BCG assemblies and other small parts - but those are steel, anyway. For large enough tanks, handguns can just be dropped in the basket with the slide locked open, or cylinder swung out. Single actions I disassemble and drop the frame and cylinder as two pieces.

Quote:

---

Originally Posted by Brian

Sorry, I didn't word that very well, but that was my point. I've heard very mixed reviews on what you can and cannot use in one of these. Hornady clearly advertises it's made for cleaning upper receiver groups and small parts, but then the vast "wisdom" of the internet seems to claim you can't dump your lower in it, or it will dissolve into fairy dust or something. I shoot a lot suppressed, and the idea that I could disassemble the gun and drop it in a tank, dirty mags and all, is really appealing. But not if it's going to somehow mess with the anodizing or something.

Would really like to hear from someone who has dunked their AR a few dozen times.

---

Quote:

---

Originally Posted by sniper7

What is an areare-15 upper receiver made of?

---

Evil. They're made of racist evil.

As for lube...
In normal conditions, some light grease (something that won't run) on the contact areas of the BCG, the contact areas of the bolt, and a little itty bitty bit on the buffer and the hammer face.
In dirty environments, spray-on dry lube on everything.
In humid environments, lube with grass as above, then get your hands a little greasy and run your hand over everything steel... better to clean a little grease off your uniform than spend an hour scrubbing rust off your FSP after a week in the field.