Taylor Tuned Smoke Wagon. Action is SWEET!
https://www.taylorsfirearms.com/medi...e95/s/w/sw.jpg
Printable View
Taylor Tuned Smoke Wagon. Action is SWEET!
https://www.taylorsfirearms.com/medi...e95/s/w/sw.jpg
That's the good stuff from Wyo, shoots close to 25' stream on a good day. We lit one off in front of jensens years ago, to see how far it went compared to mfg claim. .Quote:
Originally Posted by MrPrena
I did. Sold off all the guns a while ago. Still trying to sell all the clothes. Then I realized how much I missed owning a SAA clone. I really enjoy the experience of shooting them. I just enjoy plinking with them.Quote:
Originally Posted by HBARleatherneck
In hindsight, I should have kept one of the revolvers. On the plus side, I have an even nicer action and no transfer bar (it has a saftey that doesn't lock the firing pin on the hammer in place unless you're pulling the trigger). The downside is I spent more money.
Where did you find that deal?Quote:
Originally Posted by MrPrena
Ditto, I'd be interested as well at that price.Quote:
Originally Posted by MrPrena
Quote:
Originally Posted by Irving
Quote:
Originally Posted by ChickNorris
https://i.imgur.com/07Ma0Te.jpgQuote:
Originally Posted by ChickNorris
Thumbs up.
: )Quote:
Originally Posted by Irving
Good job, but doesn't one normally use a case spreader instead of beating it in?
P.S. Don't know if you FB, but there's a "Built Not Bought" page that's pretty cool.
A case spreader does make it a lot easier but only really needed when doing it a lot or setting up new gears, For just removing and re-installing prying and hammering is ok. Plus a case spreader is expensive.Quote:
Originally Posted by brutal
You could mock something up to use that full hydro setup. LOLQuote:
Originally Posted by newracer
Two AR pistols and my can is out of jail.
Attachment 76155
I copied another member's gun and made myself a lightweight 10/22. Can't wait to get this thing up and running.
https://lh3.googleusercontent.com/XP...=w1113-h626-no
https://lh3.googleusercontent.com/Nm...=w1113-h626-no
Can't really take a picture of it but purchased my first shooting range membership at NCRGC. Hoping to try my hand at some steel challenge.
Attachment 76167
A Halloween costume for a 10/22.
You don't need to be a member to attend comps, there or any other membership range. I have my gate card for wcfw good till dec if you need it ;)Quote:
Originally Posted by SouthPaw
New for me anyway. 09 tlz fully loaded picked it up with only 83,000 miles on it. https://uploads.tapatalk-cdn.com/201...49fe401578.jpg
Sent from my SM-N910V using Tapatalk
That's a stock photo.
Sent from my SM-N910V using Tapatalk
Nothing like percolating coffee over a campfire.
https://i.imgur.com/ujqO4rV.jpg
https://www.brownells.com/userdocs/p...00404361_1.jpg
$389 net cost at Brownells with a $20 coupon code (M8Y).
https://www.brownells.com/firearms/h...prod92136.aspx
I dont care what most people say this place is way better than In-N-Out. luckily I'll be back in Guymon Monday afternoon.Quote:
Originally Posted by Fentonite
The Firing Line in Aurora has had one of those things for sale for as long as I can remember (seriously at least 7 or 8 years).Quote:
Originally Posted by SAnd
Damn...that's a lotta fence. Looks nice, too.
Under 5 cents per round from PSA w/free shipping:
Attachment 76186
Choot Em will never die.
New toy
https://www.ar-15.co/attachment.php?...9&d=1537921936
ATTACH=CONFIG]76199[/ATTACH]
Nifty rig, I need one for moose season. Let me borrow it and you can use my chain saw. ;)
Great, thanks to that incident,if I wanna borrow a chainsaw here,I have less than 1% chance to borrow it here.
That looks expensive. New or used?Quote:
Originally Posted by 00tec
Used. New would be nice, but as our first machine, we didn't really feel the need to drop a ton of coin on it. Got it for just over 12.Quote:
Originally Posted by ray1970
Nice deal. Been looking at used ones here, but have a garage to build first.Quote:
Originally Posted by 00tec
Doing the work yourself?Quote:
Originally Posted by newracer
I assume you checked the TBA with vag already?
Curious minds wanna know ('03 A6 2.7T)
This is for my sons '05 A4 1.8T Quattro.
I had the car at the dealer for some other work and they said the throttle body was bad, I don't remember the code it was throwing. Dealer wanted almost $800 to replace. Bought a Bosch OEM from Advanced for $130 and replaced it last night in about 20 minutes. Also recently replaced the accelerator pedal assembly. All seems good now.
Bought some plastidip and sprayed the top layer of foam in my gun case. From what I read it keeps the foam together better over time. I guess we will see.
https://uploads.tapatalk-cdn.com/201...55cad0f557.jpg
My 10 year anniversary gift from my wifehttps://uploads.tapatalk-cdn.com/201...f92b77ae85.jpg
Sent from my SM-N910V using Tapatalk
Havalon Piranta Edge with interchangeable scalpel blades for field dressing and caping chores.
https://www.ar-15.co/attachment.php?...7&d=1538167152
Attachment 76217
Red paint to refurbish some vintage meat hooks for handling moose quarters in the field.
https://www.ar-15.co/attachment.php?...8&d=1538167203
Attachment 76218
Carbon Z Trekkers
https://www.ar-15.co/attachment.php?...9&d=1538168339
Attachment 76219
A newly sharpened Pac-Saw. Have used it 30 years and it was past time....
https://www.ar-15.co/attachment.php?...0&d=1538168547
Attachment 76220
Found these cheap on Massdrop (millenial webstore that creates sale prices by organizing group buys). Something like 40% off.
I like it thus far. Not in the same class as my ZT or Emerson, but for a cheap ($40) pocket knife that I can have a few of for each vehicle and not really worry if I trash it, it works pretty good. The bearing based flipper construction takes a minute to get used to, but it becomes pretty natural.
D2 Tool Steel, G10 Scales, and Stainless chassis, so decent materials too.
https://farm2.staticflickr.com/1901/...7d21f068_c.jpgNew Knife by ARNEWB, on Flickr
New EDC blade, razor sharp from the factory and CO legal!
https://uploads.tapatalk-cdn.com/201...d9b1ab899d.jpg