The post whore thread.

Quote:

---

Originally Posted by HoneyBadger

I use a lee turret press. It does the job well enough. Sometimes reloading is a pain, especially when it's trimming time. I need a better trimmer.

---

Did you ever get the Worlds Finest Trimmer?

Quote:

---

Originally Posted by hghclsswhitetrsh

http://www.giraudtool.com/Tri%20Way%20Trimmer.htm

---

Wait, they make something under $100?! How come I didn't know about this when I bought my WFT, it would be so much easier since it chamfers/deburrs in one!

Quote:

---

Originally Posted by hghclsswhitetrsh

http://www.giraudtool.com/Tri%20Way%20Trimmer.htm

---

I was just looking at that. Secretly, I think I told you to do that, but only telepathically.

Quote:

---

Originally Posted by hghclsswhitetrsh

http://www.giraudtool.com/Tri%20Way%20Trimmer.htm

---

I'm currently looking at that one.

Quote:

---

Originally Posted by BuffCyclist

Did you ever get the Worlds Finest Trimmer?

---

Nope. I wasn't convinced it was worth my monies. I have 2000+ cases that need trimming that I'm holding off on until I decide on a trimmer.

Quote:

---

Originally Posted by BuffCyclist

Jeez, if you guys are using the equivalent of Snap-on or Proto presses, then I'm using that free "wrench" they include when you buy a bookcase from Walmart.

---

be surprised how many folks never heard of proto. I have them, williams, blue points and early craftsman in service.

Quote:

---

Originally Posted by HoneyBadger

I use a lee turret press. It does the job well enough. Sometimes reloading is a pain, especially when it's trimming time. I need a better trimmer.

---

Cry once
http://www.giraudtool.com/prod02.htm

OR to mount on any press
http://www.dillonprecision.com/#/con...B_Case_Trimmer

with one of these
http://www.dillonprecision.com/#/con..._Size_Trim_Die

Quote:

---

Originally Posted by Great-Kazoo

Cry once
http://www.giraudtool.com/prod02.htm

OR to mount on any press
http://www.dillonprecision.com/#/con...B_Case_Trimmer

with one of these
http://www.dillonprecision.com/#/con..._Size_Trim_Die

---

$440?
[hahhah-no]

Quote:

---

Originally Posted by HoneyBadger

$440?
[hahhah-no]

---

Yea, what he said.

That doesn't fall into the buy-once-cry-once mentality. It falls into the I-cry-every-night-because-my-wife-found-out-I-spent-$440-on-a-brass-trimmer-and-she-beats-me category.

How dare you even consider rubbing that in our faces! [Slap]

Quote:

---

Originally Posted by HoneyBadger

I'm currently looking at that one.

Nope. I wasn't convinced it was worth my monies. I have 2000+ cases that need trimming that I'm holding off on until I decide on a trimmer.

---

You know, $440/2000 equals $0.22/case. So you can either buy new brass that's already trimmed, or buy a trimmer, trim it all and then have a fancy new tool.

[Peer Pressure!]

Quote:

---

Originally Posted by BuffCyclist

Yea, what he said.

That doesn't fall into the buy-once-cry-once mentality. It falls into the I-cry-every-night-because-my-wife-found-out-I-spent-$440-on-a-brass-trimmer-and-she-beats-me category.

How dare you even consider rubbing that in our faces! [Slap]

---

Hahahaha yup!