Shooting Ear Muffs to a two way radio how do I pull it off?

http://www.publicsafetycenter.com/im...rmuff-1375.jpghttp://ecx.images-amazon.com/images/...BL._SY300_.jpg


Ok so I want to hook up a set of Howard Leight Impact Sport electronic ear muffs to my Motorola two way radios. The radios have an input jack for a microphone, the radio has a vox feature that goes with the microphone and the headphones have an input jack for audio. This seems like it should be an easy thing to do but after an hour of searching I can not figure it out. So I need a boom microphone of some sort that I can attach to the headphones or a shirt or ? and it needs to be able to use the headphones as the audio and send the mic to the radio. Any Ideas?

Duct tape. Seriously though, I think all you would need is an auxiliary cable.

Attachment 23593

Try one of these. It doesn't utilize the aux in on the ear muffs, but the earpiece should fit just fine underneath.

ETA: I don't think VOX will work, just PTT.

VOX always seems to suck .... use PTT.

Ask the guys at Peltor. They've been making them for a while:

http://www.envirosafetyproducts.com/...-headsets.html

http://www.envirosafetyproducts.com/...adset-2209.jpg

Pretty sweet, but the ones I would want are $800. Yikes.

Yeah...they're proud of them.

Quote:

---

Originally Posted by DavieD55

Duct tape. Seriously though, I think all you would need is an auxiliary cable.

Attachment 23593

---

Its a 2.5mm jack on the radio, not 3.5, and it has contacts for mic and mono speaker.

Here is what you need to connect. You would have to use the mic on the radio though, it would only get audio into your muffs:

https://buy.garmin.com/shop/shop.do?pID=853

Then you would need a 3.5mm to 3.5mm cable like pictured above to work with this adapter.

So how far away are you trying to communicate?

If you're just wanting to talk to your buddy at the next bench over, just get a set of regular Peltor type noise canceling headphones (or just stick with your Howard Leight Impact Sport electronic ear muffs). They amplify quiet sounds (like speech) and cut out the BANG to protect your hearing.

I've been at the range with a friend with both of us wearing peltors and we're talking to each other in almost a low whisper even though we're 30ft or so apart.

Have you seen the Motorola muffs http://www.petra.com/motorola-mhp81-...-headset.html? The cable that comes with them would probably work with your Howard Leights. The cable is probably just one of these http://www.motorola.com/Business/US-...ne-53727_US-EN with the earbud cut off and a 3.5mm jack in it's place to plug into the muffs.

Quote:

---

Originally Posted by RedDogFabrication

http://www.publicsafetycenter.com/im...rmuff-1375.jpghttp://ecx.images-amazon.com/images/...BL._SY300_.jpg


Ok so I want to hook up a set of Howard Leight Impact Sport electronic ear muffs to my Motorola two way radios. The radios have an input jack for a microphone, the radio has a vox feature that goes with the microphone and the headphones have an input jack for audio. This seems like it should be an easy thing to do but after an hour of searching I can not figure it out. So I need a boom microphone of some sort that I can attach to the headphones or a shirt or ? and it needs to be able to use the headphones as the audio and send the mic to the radio. Any Ideas?

---

You can't wire (headphone) input > (radio) input and expect to get anything. The muffs in question don't have a mic input, and that is going to prevent you from using them to send input to the radio. If the radio has an "output" you can use an auxiliary cable to get audio into your muffs, but that's going to be the limit of the gear you've specified.

Thank you Josh, after looking it over I think I was over thinking it a bit, the electronic muffs do a good job re broadcasting the transmission in the headphones . I think I may just get a boom mic for the radio and call it good. On a side not the Electronic muff I went with are awesome!

Jup the Leight Impact Sports are a fantastic muffs. Picked up my first pair on Monday. They are replacing Peltor 6S muffs - finger breakers. The left muff has a serious AGC problem with take off sqeualing feedback.