Close
Results 1 to 10 of 20

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    No Nickname
    Join Date
    Jan 2011
    Location
    Parker, Colorado
    Posts
    839

    Default

    Missed the post about the low compression on #7. If doing a reman engine, you will want the shop to find out what happened. If there was a bad injector,etc that led to a burnt valve, and so on, you want that fixed. May want to look at either a Jasper engine, or a FoMoCo reman.

  2. #2
    Gong Shooter gcrookston's Avatar
    Join Date
    Aug 2010
    Location
    Centennial
    Posts
    356

    Default

    Thanks for everyone's input. After calls and crunching numbers, I think the best route is to through a new spark plug in the hole and hope it makes it by the used manager on a trade...

    By the way, did find a remain long block for $2200 @ rydells. But shop rate is 18 hours.

    If it will last a couple hundred miles maybe I can get me a newer, lower mileage Suburban (their prices are really depressed with $4/g gas)...
    "The trouble with the internet is validating sources"-- Abraham Lincoln

    "Don't believe everything you read on the internet. That's how World War One started"-- Gen. Curtis E. LeMay

  3. #3
    Guest
    Join Date
    May 2009
    Location
    Bailey, CO
    Posts
    1,511

    Default

    Quote Originally Posted by streetglideok View Post
    May want to look at either a Jasper engine, or a FoMoCo reman.

    Personal experience, I spent the big $$$ for a Jasper, it went 2k the first go, was replaced, went 50 miles, was replaced again under warranty, third engine made it out of the garage, was then told they didn't care about the warranty and I was on my own.
    Seems like everyone else has great luck with them.

    As for used 5.4's, seems that used trucks are a bit cheaper here (NE) because they use salt on the roads so cars rust early here. You could find a cheap used truck, I could verify it runs good and bring it out to Colo on my weekend returns home. Just a thought.

  4. #4
    Machine Gunner
    Join Date
    Mar 2010
    Location
    Cheyenne, Wyoming
    Posts
    1,530

    Default

    Quote Originally Posted by blackford76 View Post
    Personal experience, I spent the big $$$ for a Jasper, it went 2k the first go, was replaced, went 50 miles, was replaced again under warranty, third engine made it out of the garage, was then told they didn't care about the warranty and I was on my own.
    Seems like everyone else has great luck with them.

    As for used 5.4's, seems that used trucks are a bit cheaper here (NE) because they use salt on the roads so cars rust early here. You could find a cheap used truck, I could verify it runs good and bring it out to Colo on my weekend returns home. Just a thought.
    I would agree, Jasper is garbage. And they don't stand behind the warranty. They will find every excuse in the book to get out of a warranty claim and tell you it's your fault.

  5. #5
    Beer Meister DFBrews's Avatar
    Join Date
    Dec 2010
    Location
    With the classyish Hipsters...Stapleton
    Posts
    3,176

    Default

    If you decide to throw a used short block in it I would roll bearings in it while you are there.

    The fractured rods and mains make that bottom end bullet proof for the most part but bearings are a wear item.
    You sir, are a specialist in the art of discovering a welcoming outcome of a particular situation....not a mechanic.

    My feedback add 11-12 ish before the great servpocaylpse of 2012

  6. #6
    Gong Shooter gcrookston's Avatar
    Join Date
    Aug 2010
    Location
    Centennial
    Posts
    356

    Default Update

    Got $4,900.00 in trade...
    "The trouble with the internet is validating sources"-- Abraham Lincoln

    "Don't believe everything you read on the internet. That's how World War One started"-- Gen. Curtis E. LeMay

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •