Close
Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Ammocurious Rucker61's Avatar
    Join Date
    May 2012
    Location
    Fort Collins, CO, USA
    Posts
    3,359

    Default .308 Brass Question

    I shoot .308 in a Tikka T3 for target shooting and hunting. Last summer I shot up about 500 rounds of Freedom Munition remanufactured .308 and kept the brass in case I wanted to start reloading. I'm starting to reload now, and with new .308 brass almost impossible to find, I decided to start working to use what I have. I've cleaned and deprimed 200 rounds of the 500 pieces of brass. It's about 50% Lake City and the rest is a mix of headstamps showing SBS, PMJ, Federal, TAA06 and WCC. A random sampling shows that length of the brass varies between 2.015 and 2.020, mainly on the low side. Freedom says that they don't use crimped primer pockets on their LC.

    My primary use will be for target and hunting. Is this brass worth refurbishing if I want the maximum energy and velocity that's 1 MOA accurate for 150 gr bullets, or should I "bite the bullet" and pay for the expensive brass that's the only stuff readily available?

  2. #2
    MODFATHER cstone's Avatar
    Join Date
    Mar 2010
    Location
    Baltimore, MD
    Posts
    7,472

    Default

    You are shooting it out of a bolt gun that it has already been shot out of? That brass is form fitted for that rifle and you should only need to neck size it. If the primer pockets were swaged by Freedom, then all you need to do is neck size, prime, charge, and seat bullets. Work up your recipe in groups of five or ten to find the powder charge that works best for the bullet you are using and then load the rest.

    IMO max charge is almost never the most accurate, and you will get plenty of life out of LC brass using a mid range charge.

    There are plenty of reloaders here who have lots more experience than me. Hoser, Zombie Steve, ChaLee, etc...

    Be safe.
    Corruptissima re publica plurimae leges.

    My Feedback

  3. #3
    Ammocurious Rucker61's Avatar
    Join Date
    May 2012
    Location
    Fort Collins, CO, USA
    Posts
    3,359

    Default

    So even though the brass is 10 thousandths longer than recommended, I shouldn't need to trim with a neck sizing die? What about the 200 I ran through a FL die?

  4. #4
    At least my tag is unmolested
    Join Date
    Oct 2010
    Location
    CANON CITY, CO
    Posts
    3,133

    Default

    At 2.015" the brass is at SAAMI max length, so you could trim it up a touch. I'd probably recommend trimming it all down to around 2.005"

    It is possible to get 1 MOA from mixed headstamp brass, but its ain't likely. I'd sort out the largest single headstamp and do most of my reloading with that brass.
    Last edited by spqrzilla; 01-01-2013 at 12:31.
    Sayonara

  5. #5
    Paper Hunter mtik00's Avatar
    Join Date
    Sep 2010
    Location
    Colorado Springs
    Posts
    131

    Default Re: .308 Brass Question

    I'm really interested in this too. I did the same thing with Freedom brass. I was using their blaster ammo in my Savage ( new shooter ). I did notice a huge difference in point of impact with the different brass. I don't think it was all me, but who knows.

  6. #6
    Paper Hunter dtbighit's Avatar
    Join Date
    Mar 2011
    Location
    Denver
    Posts
    218

    Default

    Quote Originally Posted by Rucker61 View Post
    I shoot .308 in a Tikka T3 for target shooting and hunting. Last summer I shot up about 500 rounds of Freedom Munition remanufactured .308 and kept the brass in case I wanted to start reloading. I'm starting to reload now, and with new .308 brass almost impossible to find, I decided to start working to use what I have. I've cleaned and deprimed 200 rounds of the 500 pieces of brass. It's about 50% Lake City and the rest is a mix of headstamps showing SBS, PMJ, Federal, TAA06 and WCC. A random sampling shows that length of the brass varies between 2.015 and 2.020, mainly on the low side. Freedom says that they don't use crimped primer pockets on their LC.

    My primary use will be for target and hunting. Is this brass worth refurbishing if I want the maximum energy and velocity that's 1 MOA accurate for 150 gr bullets, or should I "bite the bullet" and pay for the expensive brass that's the only stuff readily available?
    Just bite the bullet and get new brass,ill take your old brass
    Is that right???just begin!!

  7. #7
    Stircrazy Jer jerrymrc's Avatar
    Join Date
    Jan 2004
    Location
    Colorado Springs
    Posts
    8,166

    Default

    I can tell you there is a big difference volume wise between LC and PMJ. I did some tests years ago and while unscientific I sized each and then trimmed. Then I filled with a small ball powder and carded off the top. I then weighed each of the charges. As you can see many like to claim that Military brass has less volume but sometimes this is not true.

    I do not have it written down in my load book but I keep thinking that there was about 100FPS difference between PMJ and LC all else being equal. And I myself keep headstamps separate except for the M80 pulls that go into the plinking ammo.

    Results

    LC= 52.4
    AFF91= 52.8
    FC= 55.2
    Hurtenburger= 54.1
    PMJ= 54.8
    I see you running, tell me what your running from

    Nobody's coming, what ya do that was so wrong.

  8. #8
    Rabid Anti-Dentite Hoser's Avatar
    Join Date
    Aug 2003
    Location
    KCOS
    Posts
    9,180

    Default

    When you are poking holes in paper and critters, try to use the same flavor of brass trimmed to the same OAL.

    For plinking and shooting dirt, any old flavor of brass will work.

    I would trim all your brass back to minimum and check it after a reload or two.

    For target ammo, neck only sizing is fine. For hunting ammo I would FL resize without a doubt.
    You know I like my coffee sweet in the morning
    and I'm crazy about my tea at night

  9. #9
    Ammocurious Rucker61's Avatar
    Join Date
    May 2012
    Location
    Fort Collins, CO, USA
    Posts
    3,359

    Default

    Quote Originally Posted by dtbighit View Post
    Just bite the bullet and get new brass,ill take your old brass
    What is this "new brass" you speak of? I can't find any .308 anywhere.

    Also, I haven't invested in a trimmer or case prep power tool yet. What's the going rate for case prep, or just trimming?
    Last edited by Rucker61; 01-01-2013 at 15:11.

  10. #10
    Paper Hunter dtbighit's Avatar
    Join Date
    Mar 2011
    Location
    Denver
    Posts
    218

    Default

    Quote Originally Posted by Rucker61 View Post
    What is this "new brass" you speak of? I can't find any .308 anywhere.

    Also, I haven't invested in a trimmer or case prep power tool yet. What's the going rate for case prep, or just trimming?
    I know you can't find brass anywhere,you can order a Lee case trimmer and lock stud for cheap and do it by hand,its slow but yields good results for me,when I do .308 I take my time and don't load in volume anyway
    Is that right???just begin!!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •