Um,,,, instructions?

Quote:

---

Originally Posted by colorider

Yes it's an AR and I'm only assembling the lower receiver, grip, stock , then putting the upper/lower together. The upper was purchase completely assembled.

---

Watch all the videos, then give it a try. Either way, when you are finished, take it to Bert ( he is pretty close to Westminster) or Rob down at Bowers. They will fix or safety anything you have done incorrectly and probably provide half a semester of valuable information along the way.

You don't know what you don't know until you find out what you didn't know.

Just my $.02 [Coffee]

Quote:

---

Originally Posted by Fist_gonzo

Holy shit you building a space shuttle?[ROFL1]

---

Lego's. [LOL][Coffee][Flower]

Quote:

---

Originally Posted by cstone

Wait, I'm confused. Bert, was that for an AR15, AR10, or an AR57. Does that include the upper, lower and middle?

While you are at it, could you check the headspace on my plasma rifle?

All in fun. [ROFL1]

---

Applies to all AR variants. Deviations may occur in procedure depending on variations in part H. Parts I (2 ea) may be deleted on variants of part H to be replaced with parts O and P as required.


Just what you see here buddy....................

Quote:

---

Originally Posted by BPTactical

While holding part B in place securely on part A place assembly into place on part C and slide part D into place. Use care to ensure proper tension on part B.
Insert part E into part C. Lightly lubricate the threads on part C and screw on part F, making sure to allow for clearance of part G which at this time should be attached to part H. If there is not clearance for part G lightly snug part F, using care to not over torque. Place part H over part E and slide towards the junction of part C and E. Ensure alignment of part G with the hole in part F and alignment of E and C. Ensure vertical alignment of part H relative to part C. While holding part H securely drill 2 holes to intersect the junction of part E and H. Taper ream holes 2 each from left to right taking care not to ream too deeply. Drive part I (2 each) to seat firmly in taper holes intersecting parts H and E. Using the appropriate fixture screw part J onto part E with part K facing tapered side towards part C securely into place ensuring alignment of the center slot in part J vertically.
Insert the assembly of part L and M into the hole on the right rear of part C and while holding the assembly of part L and M compressed drive part N into place.

That completes assembly of component #1.

Let me know when your are ready to assemble component 2

---

You copied that from some of that made in Taiwan, assemble it yourself furniture, didn't you? [Coffee]

Quote:

---

Originally Posted by ray1970

You copied that from some of that made in Taiwan, assemble it yourself furniture, didn't you? [Coffee]

---

You must be talking about the furniture that takes a small drill bit then a tad bigger drywall screw so well instead of crazy twisty locks and stuff. [LOL]

Scary thing is, if you decipher the part designations and really read it is in fact a "loose"procedural guide for assembling an upper assembly.

Quote:

---

Originally Posted by BPTactical

While holding part B in place securely on part A place assembly into place on part C and slide part D into place. Use care to ensure proper tension on part B.
Insert part E into part C. Lightly lubricate the threads on part C and screw on part F, making sure to allow for clearance of part G which at this time should be attached to part H. If there is not clearance for part G lightly snug part F, using care to not over torque. Place part H over part E and slide towards the junction of part C and E. Ensure alignment of part G with the hole in part F and alignment of E and C. Ensure vertical alignment of part H relative to part C. While holding part H securely drill 2 holes to intersect the junction of part E and H. Taper ream holes 2 each from left to right taking care not to ream too deeply. Drive part I (2 each) to seat firmly in taper holes intersecting parts H and E. Using the appropriate fixture screw part J onto part E with part K facing tapered side towards part C securely into place ensuring alignment of the center slot in part J vertically.
Insert the assembly of part L and M into the hole on the right rear of part C and while holding the assembly of part L and M compressed drive part N into place.

That completes assembly of component #1.

---

Yeah... but you forgot to mention that for the "Lefty Version", all of that is done in "mirror-image" and in reverse order. [LOL]