Close
Page 2 of 4 FirstFirst 1234 LastLast
Results 11 to 20 of 34
  1. #11
    If I had a son he would look like....Ben SideShow Bob's Avatar
    Join Date
    Mar 2010
    Location
    SE Aurora
    Posts
    7,120

    Default

    But for the fact that the OP fired another 200 rounds with out this happening again, hammer follow is unlikely. Hammer follow would have happened again a least a few if not numerous times.
    My T.P. wheeling and dealing feedback is here.

    Opinions are like assholes, everybody has one, and it stinks more than mine.


    Yo Homie, That my chainsaw ?



    Pati, improbe et vince

  2. #12
    QUITTER Irving's Avatar
    Join Date
    Nov 2008
    Location
    Denver, CO
    Posts
    46,527
    Blog Entries
    1

    Default

    Is it less hard on the gun to do the hammer follow test with snap-caps?
    "There are no finger prints under water."

  3. #13
    If I had a son he would look like....Ben SideShow Bob's Avatar
    Join Date
    Mar 2010
    Location
    SE Aurora
    Posts
    7,120

    Default

    Quote Originally Posted by Irving View Post
    Is it less hard on the gun to do the hammer follow test with snap-caps?
    With snap caps you don't get the full force slam / jar to cause the slip on the full cock notch.
    My T.P. wheeling and dealing feedback is here.

    Opinions are like assholes, everybody has one, and it stinks more than mine.


    Yo Homie, That my chainsaw ?



    Pati, improbe et vince

  4. #14
    Ammosexual GilpinGuy's Avatar
    Join Date
    Mar 2012
    Location
    Rural Gilpin County
    Posts
    7,221

    Default

    Scary as shit. My bud had a shotgun go off when he pumped it between clay birds. No finger on the trigger. After all the "wtf"s and "holy shit"s he did it over and over again.

    Edit: What i mean is that every time he pumped the shotgun, it went off. We were testing it before continuing with the clay birds.

    This happened 10 years ago or so. It was a HUGE lesson for me.

  5. #15
    QUITTER Irving's Avatar
    Join Date
    Nov 2008
    Location
    Denver, CO
    Posts
    46,527
    Blog Entries
    1

    Default

    Quote Originally Posted by SideShow Bob View Post
    With snap caps you don't get the full force slam / jar to cause the slip on the full cock notch.
    Then how did it happen with live ammo in the chamber? Are you saying it can still happen with ammo (obviously) but it's more likely to happen (and then be discovered) when empty?
    "There are no finger prints under water."

  6. #16
    If I had a son he would look like....Ben SideShow Bob's Avatar
    Join Date
    Mar 2010
    Location
    SE Aurora
    Posts
    7,120

    Default

    I've had a stuck firing pin go full auto (luckily with only three rounds left in the magazine) due to a filthy pistol. And a slam fire from a protruding primer.
    A hammer follow would be a mechanical problem that would have repeated itself while continuing shooting.
    The empty chamber test is what should be done sparingly, usually after trigger work is done or for a suspected problem.

    And yes, it is more likely to be found when the slide is dropped on an empty chamber.
    Last edited by SideShow Bob; 06-05-2016 at 23:10.
    My T.P. wheeling and dealing feedback is here.

    Opinions are like assholes, everybody has one, and it stinks more than mine.


    Yo Homie, That my chainsaw ?



    Pati, improbe et vince

  7. #17
    Grand Master Know It All
    Join Date
    Mar 2006
    Location
    Dickshooter, ID
    Posts
    4,828

    Default

    I cannot understand why racking the slide would be considered hard on the gun?

  8. #18
    If I had a son he would look like....Ben SideShow Bob's Avatar
    Join Date
    Mar 2010
    Location
    SE Aurora
    Posts
    7,120

    Default

    Quote Originally Posted by Wulf202 View Post
    I cannot understand why racking the slide would be considered hard on the gun?
    It's not racking the slide , it is letting it slam home on an empty chamber that is not good for it. Without stripping a round & chambering to slow the momentum, the slide slams home under full force of the recoil spring. This will cause wear, peening and eventually breakage of the associated parts of the slide, barrel, barrel lugs, link and slide stop shaft.

    And with the title of "Grand Master Know it all" you shouldn't need to ask this !
    Last edited by SideShow Bob; 06-06-2016 at 05:21.
    My T.P. wheeling and dealing feedback is here.

    Opinions are like assholes, everybody has one, and it stinks more than mine.


    Yo Homie, That my chainsaw ?



    Pati, improbe et vince

  9. #19
    Ryobi Robb Robb's Avatar
    Join Date
    Jan 2007
    Location
    Thornton, CO
    Posts
    1,222

    Default

    Dropping the slide on an empty chamber messes up your high dollar trigger job on a 1911, or so I've read.
    Something about battering the sear, or sear bounce, or some such. It may not be hard on a stock gun, but after you just paid for a trigger job you don't want to be dropping the slide on an empty chamber over and over.

    I saw all this too late last night, I'll test it out tonight and report back.

  10. #20
    Grand Master Know It All
    Join Date
    Mar 2006
    Location
    Dickshooter, ID
    Posts
    4,828

    Default

    Click image for larger version. 

Name:	20160606_080847.jpg 
Views:	99 
Size:	241.3 KB 
ID:	65753

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •